配置接口IP地址并通過靜態路由、默認路由配置實現全網互通！

配置接口IP地址并通過靜態路由、默認路由配置實現全網互通
1.對Router-R1/R3進行默認路由配置，R2為靜態路由配置

2.配置好PC機的IP地址，子網掩碼，網關之后，開始配置路由R1/2/3/的IP地址。

<Huawei> //用戶視圖
<Huawei>system-view //在用戶視圖下輸入命令行進入系統視圖
[R1]interface GigabitEthernet 0/0/1 //進圖接口視圖
[R1-GigabitEthernet0/0/1]ip address 192.168.1.254 255.255.255.0 //為0/0/1接口配置IP地址
[R1-GigabitEthernet0/0/1]interface GigabitEthernet 0/0/0
//進圖接口視圖
[R1-GigabitEthernet0/0/0]ip address 192.168.2.1
255.255.255.0 //為0/0/1接口配置IP地址

<Huawei>
<Huawei>system-view
[R2]interface GigabitEthernet 0/0/1
[R2-GigabitEthernet0/0/0]IP address 192.168.2.2 255.255.255.0
[R2-GigabitEthernet0/0/0]interface GigabitEthernet 0/0/1
[R2-GigabitEthernet0/0/1]ip address 192.168.3.2 255.255.255.0

<Huawei>
<Huawei>system-view
[R3]interface GigabitEthernet 0/0/1
[R3-GigabitEthernet0/0/1]ip address 192.168.3.1 255.255.255.0
[R3-GigabitEthernet0/0/1]interface GigabitEthernet 0/0/2
[R3-GigabitEthernet0/0/2]ip address 192.168.4.254 255.255.255.0

3.為路由器配好IP地址之后開始進行靜態路由和默認路由設置

[R1-GigabitEthernet0/0/1]quit //返回上一視圖
注：quit //返回上一視圖 返回到系統視圖進行配置

[R1]ip route-static 0.0.0.0 0.0.0.0 192.168.3.2
//在系統視圖進行默認路由配置

[R2-GigabitEthernet0/0/1]quit //返回上一視圖
[R2]ip route-static 192.168.1.0 255.255.255.0 192.168.2.1
[R2]ip route-static 192.168.4.0 255.255.255.0 192.168.3.1
//在系統視圖進行默認路由配置

[R3-GigabitEthernet0/0/1]quit //返回上一視圖
注：quit //返回上一視圖
[R3]ip route-static 0.0.0.0 0.0.0.0 192.168.3.2
//在系統視圖進行默認路由配置

4.用PC-1 ping PC-4 在命令行界面輸入

用PC-1 ping PC-4

用PC-4 ping PC-1 在命令行界面輸入
ping 192.168.1.1